best security camera brand image
niceperson
I want to set up a home security camera that is motion sensitive to record video when it detects motion and record the video on my home PC. I need to know what to buy exactly, I dont' think I have a video recording card. Any brand names that are good would help and where to buy them.
Answer
There are home security shops which sell a complete kit with everything you need as you described
There are home security shops which sell a complete kit with everything you need as you described
How to install security cameras and ethernet in new home?
06Si
I am having a brand new house built, in the next couple of weeks it will be at the point where I need to install my own ethernet and security cameras before drywall goes up as the builders do not do this themselves. If anyone has any tips of how to online it will be much appreciated. I want ethernet in every room and 4 cameras out doors.
Answer
First off, plan. Walk the layout carefully and a paper map that you can mark up may be helpful as well. You can make a photocopy of a floor plan or hand draw this, it doesn't need to be exact, but you need a really good idea of where you are putting things.
Before you do anything else plan where your router will go. This is the most important thing to plan for because once the dry wall is up you will not be able to change your mind on it. Make sure to plan for any kind of ISP you may choose to have in the future, so both cable and telephone will need to be wired into this room where the router will be. That way if you decide to change ISP's they can install the modem in that same room. Trust me, nothing is worse than having your Ethernet wiring job perfect only to find out that it is then useless because you can't put the modem in the room designed for the router.
Make sure when you layout where the cables will go that they will be protected. None should be exposed to extreme heat or cold and you especially want to make sure they will not be accessible to small animals that may get under the house or into the attic. Small critters love to chew cables, they will destroy your Ethernet very fast and all will be for naught.
Install your patch panel. All of your Ethernet cables will need to run to a patch panel if you want this to look clean. I do not recommend putting the panel built into the wall, instead plan to have it in a place where you can quickly remove it from the wall so you can re-punch any runs that need it in the future.
Run the cables. Run each cable then from the patch panel to their destination making sure to leave slack at both ends, usually between 6 to 9 inches of slack on each end is plenty to then work with it. Do not punch down anything yet. Make sure when running the cable that it is out of the way of where the drywall will be installed and that you do not kink or crimp anywhere, especially around corners. A rule of thumb is that the Ethernet cable should never bend more than if you were to wrap it around your hand. That is about the tightest corner you want to make it do safely.
Attach the Ethernet cable up and out of the way using a staple gun with special wiring staples (they are wider and rounded so they don't kink the cable but you still need to be cautious when putting them in, don't puncture the cable at all) or you can use some nails hammered in on each side of the cable and bent over to hold them in place. the second method is safer but more time consuming.
When planning and running the cables run at least 1 spare to each outlet. This will help you out later if you make a mistake or need to replace one cable. You may also want to run a fish line, no not fishing line, a fish line. It can really be just about any durable string you can use to pull a cable through the wall after the drywall is in place in case you need to replace one cable.
Make sure to mark each cable on both ends. Come up with a system that works for you, I usually just number them then mark those numbers on my map. Some people designate the room the cable goes to a letter and the outlet gets a number then the port on that outlet gets a number as well so those look like: A-3-1 (just an example). By marking them all on both ends you can trace each wire out when you are ready to punch them down and know which port goes where.
Once they are all run, you have slack, you are positive they are out of the way for the dry wall to go up, just wait for the house to be finished. When it is done punch down your cables at the patch panel, punch down your ports for each outlet (don't put ports on the spare cables just leave them in the wall just for emergencies). Put your face plates up then you will need your modem plugged into your router, your router will need to plug into a switch (because you will probably need a lot more ports than a router will give you) then the switch will need to connect to your patch panel.
Once that is all connected and ready to go you will need to go around and test your ports. You may want an Ethernet tester for this to verify you have the correct pin out. I would recommend doing a search online for the pin out config.
For the security camera's I would recommend using WiFi capable cameras for outside and Ethernet connected ones for inside. Or go WiFi with all of them. Just make sure you have an electrician install a weatherproof/tamper-proof power outlet near where you want them and you are good.
First off, plan. Walk the layout carefully and a paper map that you can mark up may be helpful as well. You can make a photocopy of a floor plan or hand draw this, it doesn't need to be exact, but you need a really good idea of where you are putting things.
Before you do anything else plan where your router will go. This is the most important thing to plan for because once the dry wall is up you will not be able to change your mind on it. Make sure to plan for any kind of ISP you may choose to have in the future, so both cable and telephone will need to be wired into this room where the router will be. That way if you decide to change ISP's they can install the modem in that same room. Trust me, nothing is worse than having your Ethernet wiring job perfect only to find out that it is then useless because you can't put the modem in the room designed for the router.
Make sure when you layout where the cables will go that they will be protected. None should be exposed to extreme heat or cold and you especially want to make sure they will not be accessible to small animals that may get under the house or into the attic. Small critters love to chew cables, they will destroy your Ethernet very fast and all will be for naught.
Install your patch panel. All of your Ethernet cables will need to run to a patch panel if you want this to look clean. I do not recommend putting the panel built into the wall, instead plan to have it in a place where you can quickly remove it from the wall so you can re-punch any runs that need it in the future.
Run the cables. Run each cable then from the patch panel to their destination making sure to leave slack at both ends, usually between 6 to 9 inches of slack on each end is plenty to then work with it. Do not punch down anything yet. Make sure when running the cable that it is out of the way of where the drywall will be installed and that you do not kink or crimp anywhere, especially around corners. A rule of thumb is that the Ethernet cable should never bend more than if you were to wrap it around your hand. That is about the tightest corner you want to make it do safely.
Attach the Ethernet cable up and out of the way using a staple gun with special wiring staples (they are wider and rounded so they don't kink the cable but you still need to be cautious when putting them in, don't puncture the cable at all) or you can use some nails hammered in on each side of the cable and bent over to hold them in place. the second method is safer but more time consuming.
When planning and running the cables run at least 1 spare to each outlet. This will help you out later if you make a mistake or need to replace one cable. You may also want to run a fish line, no not fishing line, a fish line. It can really be just about any durable string you can use to pull a cable through the wall after the drywall is in place in case you need to replace one cable.
Make sure to mark each cable on both ends. Come up with a system that works for you, I usually just number them then mark those numbers on my map. Some people designate the room the cable goes to a letter and the outlet gets a number then the port on that outlet gets a number as well so those look like: A-3-1 (just an example). By marking them all on both ends you can trace each wire out when you are ready to punch them down and know which port goes where.
Once they are all run, you have slack, you are positive they are out of the way for the dry wall to go up, just wait for the house to be finished. When it is done punch down your cables at the patch panel, punch down your ports for each outlet (don't put ports on the spare cables just leave them in the wall just for emergencies). Put your face plates up then you will need your modem plugged into your router, your router will need to plug into a switch (because you will probably need a lot more ports than a router will give you) then the switch will need to connect to your patch panel.
Once that is all connected and ready to go you will need to go around and test your ports. You may want an Ethernet tester for this to verify you have the correct pin out. I would recommend doing a search online for the pin out config.
For the security camera's I would recommend using WiFi capable cameras for outside and Ethernet connected ones for inside. Or go WiFi with all of them. Just make sure you have an electrician install a weatherproof/tamper-proof power outlet near where you want them and you are good.
Powered by Yahoo! Answers
Tidak ada komentar:
Posting Komentar